Skip to content
Serving Livermore and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (650) 203-2763

AC Installation in Union City, CA

Serving Union City and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (650) 203-2763

The short answer

We install central air conditioners, heat pumps and ductless systems in Union City homes, starting with a room-by-room load calculation and a duct and electrical check so the system fits the house. Many homeowners choose a heat pump because it both cools and heats, and since incentives change, we confirm current offers before quoting them.

Adding central air to a Union City home, or replacing a system that has reached the end of its life, is a bigger decision than picking a unit off a list. The right equipment depends on your ductwork, the size and layout of your house, how quickly it gains heat on a warm afternoon, and whether you want cooling only or a heat pump that also heats. TotalFlow HVAC Repair Service travels about 14 miles from our Livermore base to install air conditioning in homes across Union City and the 94587 ZIP code. Below is how we approach an installation and what to think through before you choose a system.

Sizing the System to Your Home

An air conditioner that is too large cools the house in short bursts and shuts off before it removes much moisture, which leaves rooms feeling clammy and wears out parts faster. One that is too small runs all afternoon and still falls behind. We avoid both problems by calculating the cooling load for your house instead of copying the tonnage printed on the old unit.

That calculation looks at square footage, ceiling height, window size and direction, insulation, and air leakage. Two homes with the same floor area can need different equipment. A west-facing upstairs bedroom, for example, may need more airflow than a shaded ground-floor room of the same size, and the duct design should reflect that.

Central AC, Heat Pump or Ductless

Most Union City homeowners we talk with are choosing between three setups. Each one cools well when it is sized and installed correctly; the difference is in how it fits your house and your heating plans.

If your home also has an older gas furnace, timing matters. Under the Bay Area Air District's Rule 9-4, natural gas furnaces manufactured from 2029 must meet a zero-NOx emission standard, which in practice points homeowners toward heat pumps when a furnace is replaced after that date. The rule does not require you to replace working equipment; it applies only when a furnace fails or is replaced. Still, if you are installing new cooling now, it is worth asking whether a heat pump makes more sense than pairing a new AC with a furnace you may replace in a few years.

  • Central air conditioner: an outdoor condenser paired with your existing furnace and ductwork, a good fit when the furnace still has useful life left.
  • Heat pump: an outdoor unit that cools in summer and heats in winter, paired with an air handler or furnace, so one system covers both seasons.
  • Ductless mini-split: wall-mounted indoor heads connected to an outdoor unit, useful for homes without ducts, additions, or a converted garage.

Checking Ducts, Electrical and Placement

New equipment can only perform as well as the ducts that carry its air. Before we install, we look for leaking joints, crushed or undersized runs, and missing insulation in the attic or crawlspace. Ducts sized for an older, smaller system may need changes to deliver the airflow a new unit needs.

We also confirm your electrical panel and circuit can support the new system, and we plan where the outdoor unit will sit. It needs clear space around it for airflow, a level pad, and a spot that keeps noise away from bedroom windows, yours and your neighbors'. If you live in a townhome or a community with an HOA, check its rules on outdoor equipment early so approval does not hold up the job.

What Installation Day Looks Like

Most straightforward replacements are finished in a day, while new duct runs or a switch to a heat pump can take longer. We walk you through the plan before work starts so you know what to expect.

  • Protect floors and work areas, then shut off power and safely recover refrigerant from the old system.
  • Remove the old equipment and set the new outdoor unit, indoor coil or air handler, and line set.
  • Pressure-test and evacuate the refrigerant lines before charging the system.
  • Install and set up the thermostat, then measure airflow and temperatures to confirm the system is running as designed.
  • Show you how to operate the system and when to change the filter.

Rebates and Incentives

The federal Energy Efficient Home Improvement Credit (25C) covered qualifying heat pumps placed in service before December 31, 2025. It is not available for new installations after that date, so it will not apply to a system installed now.

Bay Area homeowners can still check BayREN and their local clean energy provider for current heat pump and electrification incentives. Amounts and availability change by funding cycle, so we confirm the current offer before including it in your quote rather than relying on last year's numbers.

More services in Union City

Related

What to expect

How a visit goes

  1. Find the cause first

    We test and inspect before recommending parts or equipment, so the fix matches the actual problem instead of a guess.

  2. Clear options, no pressure

    When a system could be repaired or replaced, we lay out both paths and the tradeoffs, then let you decide what fits your home.

  3. Current information on rules and incentives

    Air District rules and rebate programs change. We confirm what applies today before we talk about it, so you can plan with accurate information.

FAQ

Common questions

How do I know what size air conditioner my Union City home needs?

We run a load calculation that accounts for square footage, insulation, windows, sun exposure and air leakage. That tells us the right capacity for your house, which may differ from the size of your old unit.

Can I keep my existing ductwork?

Often, yes. We inspect the ducts for leaks, damage and sizing first. If they are in good shape and can handle the new system's airflow, we reuse them; if not, we explain which sections need repair or replacement.

Should I install a heat pump instead of a central AC?

If your furnace is aging, a heat pump lets one system handle both cooling and heating. If your furnace is relatively new, pairing it with a central AC can make sense. We go over both options for your home.

Do I have to replace my working gas furnace because of the new Air District rules?

No. The Bay Area Air District rules do not require replacing working equipment. They apply only when an existing furnace fails or is replaced.

Is the federal tax credit still available for a new heat pump?

No. The federal 25C credit covered qualifying heat pumps placed in service before December 31, 2025. Check BayREN and your local clean energy provider for current incentives, and we will confirm what is available when we quote.

Do you install AC in areas near Union City?

Yes. Along with Union City, we install air conditioning in Hayward, Newark, Fremont, Pleasanton and Dublin.

Need Heating or Cooling Help in Livermore?

Tell us what your system is doing, or not doing, and we'll schedule a visit to find the cause and walk you through your options.

(650) 203-2763
Call (650) 203-2763 Request Service