Skip to content
Serving Livermore and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (650) 203-2763

Furnace Repair in San Ramon, CA

Serving San Ramon and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (650) 203-2763

The short answer

TotalFlow HVAC Repair Service repairs gas furnaces in San Ramon homes, from ignition and flame sensor problems to blower and safety-switch failures. Bay Area Air District rules don't require you to replace a working furnace, so repairing a sound unit is often a sensible choice, and we'll explain the options before any work begins.

When your furnace quits on a chilly San Ramon evening, you want to know what's wrong and what it will take to get heat back. TotalFlow HVAC Repair Service drives about 10 miles from our Livermore base to homes across San Ramon in ZIP codes 94582 and 94583. We diagnose gas forced-air furnaces, explain what we find in plain language, and repair what can reasonably be repaired. If replacement makes more sense, we'll tell you why and explain how current Bay Area Air District rules affect your choices.

Furnace Problems We Fix in San Ramon Homes

Most furnace calls come down to a handful of parts: the igniter, the flame sensor, the inducer motor, the blower, the control board, and the safety switches that shut the system down when something isn't right. Many furnaces sit unused for months and then run hard once the weather turns cool and damp. A part that was already worn often gives out on the first cold night of the season.

These are the symptoms San Ramon homeowners most often describe to us:

  • The furnace runs, but the air from the vents is cool or lukewarm
  • The burners light and then shut off after a few seconds
  • You never hear the burners ignite at all
  • The blower runs nonstop, or doesn't come on
  • The furnace turns on and off in short, frequent cycles
  • Rattling, squealing, or a loud boom when the burners light
  • A blinking status light on the furnace and no heat

What Happens During a Repair Visit

We start with the basics, because a surprising number of no-heat calls trace back to a thermostat setting, a clogged filter, or a tripped switch. From there, we watch the furnace go through its startup sequence. We check that the inducer starts, the pressure switch closes, the igniter heats, the burners light and stay lit, and the blower comes on when it should. Most furnaces store fault codes, and we read them to narrow down the cause.

We also look at things that affect safety, not just comfort: the flue and venting, the burner flame, and the visible parts of the heat exchanger. Before we replace anything, we explain what failed, why it failed, and what the repair involves. That way you can make the decision with the full picture.

Repair or Replace? What the Air District Rules Mean for You

Many San Ramon homeowners have heard that gas furnaces are being phased out. Here is what the rule actually says. Under Bay Area Air District Rule 9-4, natural gas furnaces manufactured from 2029 must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when they replace a furnace after that date. The rules do not require you to replace working equipment. They apply only when an existing furnace fails or is replaced.

So if your furnace is in good shape apart from a failed part, repairing it is a reasonable choice. Replacement is worth discussing if the furnace needs frequent repairs, if parts are hard to find, or if we see heat exchanger damage. If you're weighing a heat pump, keep in mind that the federal 25C tax credit covered qualifying heat pumps placed in service before December 31, 2025, and it isn't available for new installations now. Check BayREN and your local clean energy provider for current electrification incentives. Amounts change by funding cycle, so we confirm the current offer before we discuss it with you.

When to Shut the Furnace Off Right Away

Some situations call for stopping, not troubleshooting. If you smell gas, leave the house and call your gas utility or 911 from outside. Don't flip switches or try to relight anything. If a carbon monoxide alarm goes off, get everyone outside and call for help. If you see scorch marks, smell burning, or notice soot around the furnace or registers, turn the furnace off at its switch and have it inspected before you use it again.

Quick Checks Before You Call

These checks take a few minutes and sometimes solve the problem on their own:

  • Make sure the thermostat is set to Heat, set above room temperature, and has fresh batteries if it uses them
  • Replace a dirty air filter, since a clogged filter can trip the furnace's high-limit switch
  • Confirm the furnace's power switch is on and the breaker hasn't tripped
  • Check that the front panel is fully seated, because many furnaces won't run with it loose
  • Open any closed supply registers and clear items blocking return grilles
  • On a high-efficiency furnace, look for a kinked or clogged condensate drain line

Serving San Ramon and the Surrounding Area

We work on furnaces throughout San Ramon, along with nearby Danville, Dublin, Pleasanton, Clayton, and Union City. Whether your home is in the 94582 or the 94583 ZIP code, we'll diagnose the problem, explain your options, and get your heat working again where a repair makes sense.

More services in San Ramon

Related

What to expect

How a visit goes

  1. Find the cause first

    We test and inspect before recommending parts or equipment, so the fix matches the actual problem instead of a guess.

  2. Clear options, no pressure

    When a system could be repaired or replaced, we lay out both paths and the tradeoffs, then let you decide what fits your home.

  3. Current information on rules and incentives

    Air District rules and rebate programs change. We confirm what applies today before we talk about it, so you can plan with accurate information.

FAQ

Common questions

Do I have to replace my gas furnace because of the Bay Area Air District rules?

No. The rules don't require you to replace working equipment. They apply only when an existing furnace fails or is replaced, and the zero-NOx standard covers furnaces manufactured from 2029.

Why does my furnace light and then shut off after a few seconds?

A dirty or worn flame sensor is a common cause. Other possibilities include a venting problem or a faulty pressure switch. We test each one to find the actual cause.

Is it worth repairing an older furnace?

It depends on its overall condition, how often it has needed repairs, whether parts are available, and the state of the heat exchanger. We'll give you a clear assessment so you can decide.

Can I still get a federal tax credit for a heat pump?

The federal 25C credit covered qualifying heat pumps placed in service before December 31, 2025, and it isn't available for new installations now. Check BayREN and your local clean energy provider for current incentives.

Which parts of San Ramon do you serve?

We serve homes throughout San Ramon in ZIP codes 94582 and 94583, along with Danville, Dublin, Pleasanton, Clayton, and Union City.

What should I do if I smell gas near my furnace?

Leave the house right away and call your gas utility or 911 from outside. Don't operate switches or try to relight the furnace.

Need Heating or Cooling Help in Livermore?

Tell us what your system is doing, or not doing, and we'll schedule a visit to find the cause and walk you through your options.

(650) 203-2763
Call (650) 203-2763 Request Service