Skip to content
Serving Livermore and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (650) 203-2763

Furnace Repair in Newark, CA

Serving Newark and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (650) 203-2763

The short answer

Most furnace failures in Newark homes come from a short list of parts: dirty flame sensors, worn igniters, clogged filters, and failing pressure switches or blower components. TotalFlow HVAC Repair Service diagnoses the specific cause, explains your options, and repairs working-age furnaces. Bay Area Air District rules do not force you to replace a furnace that can still be fixed.

Furnaces in Newark tend to sit idle for much of the year and then run in short bursts on cool, damp winter nights. That start-and-stop pattern wears out certain parts faster than others: igniters, flame sensors, and pressure switches. Dust also builds up during the off months, and filters often go unchanged since last winter. TotalFlow HVAC Repair Service drives about 18 miles from our base in Livermore to repair gas and electric furnaces in homes across Newark's 94560 ZIP code. We find the actual fault, explain it in plain terms, and fix it so your heat comes on when the thermostat calls for it.

Common Furnace Problems We See in Newark Homes

Most no-heat calls trace back to a handful of components. Newark winters are mild, so furnaces here rarely run for long stretches. Parts that wear from repeated start-ups tend to fail before parts that wear from long run times.

Some of these problems need only a cleaning or an adjustment. Others need a replacement part. We tell you which one you're dealing with before any work starts.

  • Furnace tries to light, then shuts off within a few seconds, often caused by a dirty flame sensor
  • Cracked or worn-out hot surface igniter
  • Blower runs but the air coming out of the vents is cool
  • Short cycling, where the furnace turns on and off every few minutes
  • A burning-dust smell that lingers well past the first few runs of the season
  • Rattling, squealing, or a loud boom at start-up
  • A blinking error code on the control board
  • No heat at all, even though the thermostat is calling for it

How a Furnace Repair Visit Works

We start by asking what you noticed: when the problem began, what the furnace does when it tries to start, and whether you've seen any error lights. Then we check the basics, including the thermostat, filter, power, and gas supply, before we move on to the furnace itself.

Next we read any control board codes and test the components involved in the startup sequence: the inducer motor, pressure switch, igniter, flame sensor, limit switch, and blower. Testing each step tells us where the sequence breaks down, so we don't swap parts on a guess.

We also look at safety items while the furnace is open. These include venting, burner flame, and signs of heat exchanger damage. If we find a condition that isn't safe to run, we explain what we found and why. Then we walk you through your options before you decide anything.

Repair or Replace? What Bay Area Rules Mean for Your Furnace

If your furnace can be repaired, you are not required to replace it. The Bay Area Air District's appliance rules apply only when an existing furnace fails or is replaced. They do not require you to remove working equipment.

Those rules do matter for planning ahead. Under the Air District's furnace rule, natural gas furnaces manufactured from 2029 on must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when they replace a furnace after that date. If your furnace is older and needs frequent repairs, it can help to know this before you decide whether to keep repairing it.

On incentives: the federal Energy Efficient Home Improvement Credit covered qualifying heat pumps placed in service before December 31, 2025. It is not available for new installations after that date. Newark homeowners can still check BayREN and their local clean energy provider for current heat pump and electrification incentives. Amounts and availability change by funding cycle, so we confirm the current offer before we mention it in any quote.

When we recommend repair or replacement, we base it on your furnace's condition, how often it has needed work, whether the heat exchanger and venting are sound, and how well it keeps your home comfortable.

Quick Checks Before You Call

A few simple checks can sometimes get your heat back on, or at least narrow down the problem. Please don't attempt repairs on gas components yourself. If you smell gas, leave the house right away and call your gas utility or 911 from outside.

  • Make sure the thermostat is set to Heat and the setpoint is above room temperature, and replace its batteries if it uses them
  • Check the air filter and replace it if it's dirty
  • Confirm the furnace door panel is fully closed, because a safety switch keeps the furnace off when it's open
  • Check the breaker and the service switch near the furnace
  • On high-efficiency furnaces, look for a clogged or kinked condensate drain line

Serving Newark and Nearby Communities

We repair furnaces throughout Newark and in nearby Alameda County and South Bay communities, including Fremont, Union City, Milpitas, Hayward, and Pleasanton. Whether you have a newer high-efficiency unit or an older furnace in a garage or attic, we'll diagnose it carefully and explain the fix before we start.

More services in Newark

Related

What to expect

How a visit goes

  1. Find the cause first

    We test and inspect before recommending parts or equipment, so the fix matches the actual problem instead of a guess.

  2. Clear options, no pressure

    When a system could be repaired or replaced, we lay out both paths and the tradeoffs, then let you decide what fits your home.

  3. Current information on rules and incentives

    Air District rules and rebate programs change. We confirm what applies today before we talk about it, so you can plan with accurate information.

FAQ

Common questions

Why does my furnace start and then shut off after a few seconds?

A dirty flame sensor is the most common cause. If the sensor can't confirm a flame, the furnace shuts off the gas for safety. Cleaning or replacing the sensor often fixes it, but we test the whole ignition sequence to make sure.

Is a burning smell normal when I first turn on my furnace?

A brief dusty smell during the first few runs of the season is common, because dust settles on the burners over the summer. If the smell lingers, smells electrical, or smells like gas, turn the furnace off and have it checked.

Do Bay Area rules require me to replace my gas furnace?

No. The Bay Area Air District rules apply only when an existing furnace fails or is replaced. A working furnace, or one that can be repaired, can stay in service.

Can I still get the federal tax credit for a heat pump?

Not for new installations. The federal Energy Efficient Home Improvement Credit covered qualifying heat pumps placed in service before December 31, 2025. Check BayREN and your local clean energy provider for current incentives.

How do I know whether to repair or replace my furnace?

It depends on the furnace's condition, how often it has needed repairs, and whether the heat exchanger and venting are sound. We explain what we find and lay out both options so you can decide.

Do you serve areas near Newark?

Yes. Besides Newark, we repair furnaces in Fremont, Union City, Milpitas, Hayward, and Pleasanton.

Need Heating or Cooling Help in Livermore?

Tell us what your system is doing, or not doing, and we'll schedule a visit to find the cause and walk you through your options.

(650) 203-2763
Call (650) 203-2763 Request Service